From the Intel® Rapid Storage Technology menu, select the RAID volume you want to delete and press. Repeat Setup 3 to 5 and Select rccfg folder and click OK to Load driverġ. Repeat Setup 3 to 5 and Select rcraid folder and click OK to Load driverħ. Select rcbottom folder and click OK to Load driverĦ. Locate the driver in the corresponding folder of the Support DVDĥ. If you don’t have optical drive ,please copy the RAID driver to a USB Driveĥ. Locate the driver in the corresponding folder of the Support DVD then click OK to continueī. If you have only one optical drive installed in your system, eject the Windows OS installation disc and replace with the motherboard Support DVD into the optical driveī.If you don’t have optical drive ,please copy the RAID driver to a USB Driveĥ. A message appears, reminding you to insert the installation media containing the driver of the RAID controller driver, Click Browse to continueĪ. When prompted to choose a type of installation, click Custom: Install Windows only (advanced).Ĥ.Follow the screen instructions to start installing Windows® 10 Boot the computer using the Windows® 10 OS installation disc. Please follow Windows Setup to Install the RAID controller driver during Windows® 10 OS installation: Q: How to Install the RAID controller driver during Windows® 10 OS installation? Select the disks that you want to create and set to ,click itemġ2. Click item and set RAID level,below is set as exampleġ1. Press “delete”key to enter BIOS when the system reboot,click page and click itemĩ. Press F10 key and click OK ,then the system will auto rebootĦ. Click item and set to ,as below picture mark red 1Ĥ. (If press “delete”key and enter BIOS ,then please press F7 key again to enter BIOS )Ģ. Power on the system and press“delete”key to enter BIOS You will lose all data on the hard disk drives when you delete a RAID set, so please back up your data before create or deleting a RAID set.ġ. ※Note:Be cautious when create or deleting a RAID set. Select the disks that you want to create and set to ,as below picture mark red 3ġ2. Set RAID capacity and click to create RAID Set RAID name ,for example :SATAHDDRAID0,as below picture mark red 1Ĭhoose RAID Level, for example :RAID0(Stripe),as below picture mark red 2 Press F7 key and enter as below pictureĩ. Press “delete”key after the system reboot and enter BIOS Ĩ. Press F10 key and click OK then the system will auto rebootħ. If you want to create M.2 Storage RAID to ,as below picture mark red 2Īs below:click and set to Ĭlick and set to ĥ. If you only create SATA RAID, then just follow next setup item and set to ,as below picture mark red 1 (If press “delete” key enter directly and then no need to press F7 key)ģ. Power on the system and press“delete”key to enter BIOS ,check the connect drive in Storage InformationĢ. Press F7 key and enter as below picture You will lose all data on the hard disk drives when you delete a RAID set, so please back up your data before create or deleting a RAID set.įollow below setup to create RAID in BIOS setup:ġ. ※ Note :Be cautious when create or deleting a RAID set. RAID 10 is data striping and data mirroring combined without parity (redundancy data) having to be calculated and written. RAID 5 :strips both data and parity information across three or more hard disk drives. RAID 1 : (Data mirroring) copies and maintains an identical image of data from one drive to a second drive. RAID 0 : (Data striping) optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks. RAID:Redundant Arrays of Independent Disks
0 Comments
Leave a Reply. |